Home > Products> Alloy steel pipes/tubes

ASTM A519 carbon and alloy steel mechanical tubing

ASTM A519 specification covers for several grades of carbon and alloy steel mechanical tubing, either hot-finished or cold-finished.
ASTM A519 carbon and alloy steel mechanical tubing
Application:
For mechanical engineering
For mechanical and pressure use,and also for transporting steam,water,gas and etc.

Size range(mm):
Out diameter:10-324mm
Wall Tickness:1-30mm
Length:14000mm max

Grade:
  • ASTM A519 1020
  • ASTM A519 1025
  • ASTM A519 1035
  • ASTM A519 1045
  • ASTM A519 4130
  • ASTM A519 4140
Note:
DN — Nominal Diameter
NPS —Nominal Pipe Size

Pipe and Tube Specifications of ASTM A519
This specification covers for several grades of carbon and alloy steel mechanical tubing, either hot-finished or cold-finished. The steel used in the mechanical tubing may be cast in ingots or may be strand cast. When steel of different grades is sequentially strand cast, identification of the resultant transition material is required. The seamless tubing is a tubular product made without a welded seam. It is usually manufactured by hot working steel, and if necessary, by subsequently cold finishing the hot-worked tubular product to produce the desired shape, dimensions and properties. The tubes shall be furnished in the following shapes: round, square, rectangular and special sections. Heat analysis shall be made to determine the percentages of the elements specified. If secondary melting processes are used, the heat analysis shall be obtained from one remelted ingot or the product of one remelted ingot of each primary melt. The tubing shall be coated with a film of oil before shaping to retard rust when specified This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
Steel grade and Chemical composition (%) of ASTM A519:

Grade

C Mn P≤ S≤ Si Cr Mo
1008

≤0.10

0.30-0.50

0.040 0.050 - - -
1010 0.08-0.13 0.30-0.60 0.040 0.050 - - -
1018 0.15-0.20 0.60-0.90 0.040 0.050 - - -
1020 0.18-0.23 0.30-0.60 0.040 0.050 - - -
1025 0.22-0.28 0.30-0.60 0.040 0.050 - - -
1026 0.22-0.28 0.60-0.90 0.040 0.050 - - -
4130 0.28-0.33 0.40-0.60 0.040 0.050 0.15-0.35 0.80-1.10 0.15-0.25
4140 0.38-0.43 0.75-1.00 0.040 0.050 0.15-0.35 0.80-1.10 0.15-0.25
Mechanical Properties of ASTM A519:
Grade Condition MPa Tenslle Point Yield Point Elongation
1020 CW

≥414

≥483
≥5%
SR ≥345 ≥448 ≥10%
A ≥193 ≥331 ≥30%
N ≥234 ≥379 ≥22%
1025 CW ≥448 ≥517 ≥5%
SR ≥379 ≥483 ≥8%
A ≥207 ≥365 ≥25%
N ≥248 ≥379 ≥22%
4130 SR ≥586 ≥724 ≥10%
A ≥379 ≥517 ≥30%
N ≥414 ≥621 ≥20%
4140 SR ≥689 ≥855 ≥10%
A ≥414 ≥552 ≥25%
N ≥621 ≥855 ≥20%
Please note the meaning of below abbreviation in table 2:
  • HR----Hot Rolled
  • CW----Cold Worked
  • SR----Stress Relieved
  • A----Annealed
  • N----Normalized
Dimension Tolerances
Pipe Type

Pipe Sizes

Tolerances

Cold Drawn

OD

≤48.3mm

±0.40mm

WT

≥60.3mm

±1%mm



Alloy steel pipes

Recommended products:

Pipe fittings
Pipe fittings are used to connect pipes.
Welded steel pipes Weld steel pipes
We produce an extensive selection of weld steel pipe
Tubing casing Tubing and Casing >>
Line pipes are used to transport oil and gas...
Ceramic-Lined Pipes
from a single spool piece to complete piping systems.
Bi Metal Clad Pipe, Bend Bi Metal Clad Pipe, Bend
Bimetal Clad Pipe are cast with mold vanishing .
Ceramic Tile Lined Pipes Ceramic Tile Lined Pipes
Ceramic Tile Lined Pipe has very uniform coating..
Pipe flanges
Pipe flange are a method of connecting pipes, valves.
Pipe Fitting Accessories
We are passionate in Stub Ends, Bolt Sets, Fasteners
Sunny Steel Blog